Popeye's Louisiana Kitchen

Observed quat sanitizer did not meet the minimum required concentration of 200 ppm to 400 ppm in the three compartment sink. PIC corrected on site by remaking the sanitizer water.

511-6-1.05(6)(n) - Manual and Mechanical Warewashing Equipment, Chemical Sanitization-Temperature, pH, Concentration, Hardness (P,Pf) (n) Manual and Mechanical Warewashing Equipment, Chemical Sanitization - Temperature, pH, Concentration, and Hardness. A chemical sanitizer used in a sanitizing solution for a manual or mechanical operation at contact times specified under subsection (8)(b)3 of this Rule shall meet the requirements specified in DPH Rule 511-6-1-.07(6)(g), shall be used in accordance with the Environmental Protection Agency (EPA)-registered label use instructions P, and shall be used as follows:

1. A chlorine solution shall have a minimum temperature based on the concentration and pH of the solution as listed in the following chart; P

Concentration Range Minimum Temperature

MG/L PH 10 or less oF (oC) PH 8 or less oF (oC)

25-49 120 (49) 120 (49)

50-99 100 (38) 75 (24)

100 55 (13) 55 (13)

2. An iodine solution shall have a minimum temperature of 68°F (20°C)P minimum concentration between 12.5 ppm and 25 ppm, P and pH of 5.0 or less or a pH no higher than the level for which the manufacturer specifies for the solution to be effective; P

3. A quaternary ammonium compound solution shall have a minimum temperature of 75ºF (24ºC), P have a concentration as specified in DPH Rule 511-6-1-.07(6)(g) and as indicated by the manufacturer’s use directions included in the labeling, P and be used only in water with 500 ppm hardness or less or in water having a hardness no greater than specified by the EPA-registered label use instructions; P

4. If another solution of a chemical specified under paragraphs 1 through 3 of this subsection is used, the permit holder shall demonstrate to the Health Authority that the solution achieves sanitization and the use of the solution shall be approved; P

5. If a chemical sanitizer other than chlorine, iodine, or a quaternary ammonium compound is used, it shall be applied in accordance with the EPA-registered label use instructions ;P and

6. If a chemical sanitizer is generated by a device located on-site at the food service establishment, it shall be used as specified in 1-5 of this subsection and shall be produced by a device that:

(i) complies with law as specified in sections 2(q)(1) and 12 of the Federal Insecticide, Fungicide, and Rodenticide Act (FIFRA), P

(ii) complies with 40 CFR 152.500 Requirement for Devices and 40 CFR 156.10 Labeling Requirements, P

(iii) displays the EPA device manufacturing facility registration number on the device, Pf and

(iv) is operated and maintained in accordance with manufacturer’s instructions. Pf.

7. On-site chemical sanitizer generating equipment with active ingredients, such as copper, must be registered as pesticides. The active ingredient may be part of the equipment or separately added.

Oberved butter stored next to the handsink. Employee observed washing hands and splashing water into the butter. PIC corrected onsite by discarding the butter. PIC will relocate the butter and toaster to prevent contamination.

511-6-1.04(4)(t) - Food Preparation (C) (t) Food Preparation. During preparation, unpackaged food shall be protected from environmental sources of contamination.

Observed a staff member waring jewelry in the front of house service area. PIC corrected on site by having the employee to remove his watch and ring. 511-6-1.03(5)(g) - Jewelry (C) (g) Jewelry. Except for a plain ring such as a wedding band food employees may not wear jewelry including medical information jewelry on their arms and hands while preparing food.

Observed build up in the vent located in the dishwasher area. PIC will have the vent cleaned immediately to prevent further dust accumulation.

511-6-1.07(5)(d) - Cleaning Ventilation System, Nuisance & Discharge Prohibition, cleaned in way not to cause contamination or create a public health hazard (C) (d) Cleaning Ventilation Systems, Nuisance and Discharge Prohibition. Intake and exhaust air ducts shall be cleaned and filters changed so they are not a source of contamination by dust, dirt, and other materials. If vented to the outside, ventilation systems may not create a public health hazard or nuisance or unlawful discharge.

Observed improper procedures being used for reheating for hot holding. Observed beans, macaroni and cheese, and gravy improperly reheated in the CVAP machine due to the Chubb warmer not working. All TCS product was observed at 120 degrees f. As a corrective action, PIC reheated all TCS foods observed in the hotel pan thawing to 165 degrees f. PIC will email a copy of the service work order for the repair of the Chubb warmer to Robert.Lewis1@dph.ga.gov.

511-6-1.04(5)(h) - Reheating for Hot holding (P) (h) Reheating for Hot Holding.

1. Except as specified under paragraphs 2, 3, and 5 of this subsection, time/temperature control for safety food that is cooked, cooled, and reheated for hot holding shall be reheated so that all parts of the food reach a temperature of at least 165°F (74°C) for 15 seconds. P

2. Except as specified under paragraph 3 of this subsection, time/temperature control for safety food reheated in a microwave oven for hot holding shall be reheated so that all parts of the food reach a temperature of at least 165°F (74°C) and the food is rotated or stirred, covered, and then allowed to stand covered for 2 minutes after reheating. P

3. Ready-to-eat time/temperature control for safety food that has been commercially processed and packaged in a food processing plant that is inspected by the food regulatory authority that has jurisdiction over the plant, shall be heated to a temperature of at least 135°F (57°C) for hot holding. P

4. Reheating for hot holding shall be done rapidly and the time the food is between the temperatures of 41°F (5°C) and 165°F (74°C) and 41°F (5°C) and 135°F (57°C) for commercially processed food, may not exceed 2 hours. P

5. Remaining unsliced portions of meat roasts that are cooked as specified under subsection (5)(a)2 of this Rule may be reheated for hot holding using the same oven parameters and minimum time and temperature conditions under which it was cooked.

Observed wiping cloth buckets containing quaternary ammonium sanitizing solution did not meet the proper minimum strength requirements of 200-400 PPM. PIC remade the sanitizer buckets. Once the correction was completed by the PIC, I observed the Quaternary Ammonium sanitizer at 200 ppm

Observed excessive build up on shelves used to store plates above the cooked chicken service area. PIC advised to clean the area prior to placing single service articles above the cooked chicken storage area.

511-6-1.05(7)(a)2,3 - Equipment, Food/Nonfood-Contact Surfaces, and Utensils, food-contact surfaces of cooking equipment & nonfood-contact surfaces free of accumulations (C) 2. The food-contact surfaces of cooking equipment and pans shall be kept free of encrusted grease deposits and other soil accumulations.

3. Nonfood-contact surfaces of equipment shall be kept free of an accumulation of dust, dirt, food residue, and other debris.

The areas around the garbage dumpster needs cleaning due to grease and accumulated debris.

Observed coleslaw, rice, and lettuce above 41F in walk in cooler. 511-6-1.04(6)(f) - Time/Temperature Control for Safety; Cold Holding (P) (f) Time/Temperature Control for Safety Food, Hot and Cold Holding. Except during preparation, cooking, or cooling, or when time is used as the public health control, time/temperature control for safety food shall be maintained at 41°F (5°C) or below or 135°F (57°C) or above, except that roasts cooked to a temperature and for a time specified in subsection (5)(a)2 of this Rule and reheated using the same temperature and time conditions as cooking may be held at a temperature of 130°F (54°C) or above. P

Observed black scratches on interior of ice machine and black accumulation on interior door hinge. Manager was advised to have machine professionally cleaned or replaced. 511-6-1.05(7)(b) - Food Contact Surfaces and Utensils - Cleaning Frequency (P, C) (b) Equipment Food-Contact Surfaces and Utensils.

1. Equipment food-contact surfaces and utensils shall be cleaned:

(i) Before each use with a different type of raw animal food such as beef, fish, lamb, pork, or poultry. It does not apply if the food-contact surface or utensil is in contact with a succession of different types of raw meat and raw poultry each requiring a higher cooking temperature as specified under DPH Rule 511-6-1.04(5)(a) than the previous type such as preparing raw pork followed by cutting raw poultry on the same cutting board; P

(ii) Each time there is a change from working with raw foods to working with ready-to-eat foods; P

(iii) Between uses with raw fruits and vegetables and with Time/Temperature Control for safety food; P

(iv) Before using or storing a food temperature measuring device; P and

(v) At any time during the operation when contamination may have occurred. P

2. Except as specified in paragraph 3 of this subsection, if used with time/temperature control for safety food, equipment food-contact surfaces and utensils shall be cleaned at least every 4 hours throughout the day. P

3. Surfaces of utensils and equipment contacting time/temperature control for safety food may be cleaned less frequently than every 4 hours if:

(i) In storage, containers of time/temperature control for safety food and their contents are maintained at temperatures specified under DPH Rule 511-6-1-.04 and the containers are cleaned when they are empty;

(ii) Utensils and equipment are used to prepare food in a refrigerated room or area that is maintained at one of the temperatures in the following chart and:

(I) The utensils and equipment are cleaned at the frequency in the following chart that corresponds to the temperature:

Temperature Cleaning Frequency

41ºF (5.0ºC) or less 24 hours

41ºF - 45ºF (>5.0ºC - 7.2ºC) 20 hours

45ºF - 50ºF (>7.2ºC - 10.0ºC) 16 hours

50ºF - 55ºF (>10.0ºC - 12.8ºC) 10 hours

and

(II) The cleaning frequency based on the ambient temperature of the refrigerated room or area is documented in the food service establishment.

(iii) Temperature measuring devices are maintained in contact with food, such as when left in a container of deli food or in a roast, held at temperatures specified under DPH Rule 511-6-1- .04;

(iv) Equipment is used for storage of packaged or unpackaged food, such as a reach-in refrigerator, and the equipment is cleaned at a frequency necessary to preclude accumulation of soil residues;

(v) The cleaning schedule is approved based on consideration of:

(I) Characteristics of the equipment and its use,

(II) The type of food involved,

(III) The amount of food residue accumulation, and

(IV) The temperature at which the food is maintained during the operation and the potential for the rapid and progressive multiplication of pathogenic or toxigenic microorganisms that are capable of causing foodborne disease; or

(vi) In-use utensils are intermittently stored in a container of water in which the water is maintained at 135ºF (57ºC) or more and the utensils and container are cleaned at least every 24 hours or at a frequency necessary to preclude accumulation of soil residues.

4. Dining counters and table-tops shall be cleaned and sanitized routinely after removing all soiled tableware and food trays shall be cleaned and sanitized after each use by one of the following methods:

(i) A two step method in which one cloth, rinsed in sanitizing solution is used to clean food debris from the surface and a second cloth in separate sanitizing solution is used to rinse;

(ii) Sanitizing solution is sprayed onto the surface and the surface is then wiped clean with a disposable towel;

(iii) If used for cleaning and sanitizing, single-use disposable sanitizer wipes shall be used in accordance with EPA-registered label use instructions; or

(iv) Other methods approved by the Health Authority.

(v) Food trays may be cleaned and sanitized the same as table ware.

5. Except when dry cleaning methods are used as specified under subsection (7)(e) of this Rule, surfaces of utensils and equipment contacting food that is not time/temperature control for safety food shall be cleaned:

(i) At any time when contamination may have occurred;

(ii) At least every 24 hours for iced tea dispensers including nozzles and consumer self-service utensils such as tongs, scoops, or ladles;

(iii) Before restocking consumer self-service equipment and utensils such as condiment dispensers and display containers; and

(iv) In equipment such as ice bins and beverage dispensing nozzles and enclosed components of equipment such as ice makers, cooking oil storage tanks and distribution lines, beverage and syrup dispensing lines or tubes, coffee bean grinders, and water vending equipment:

(I) At a frequency specified by the manufacturer; or

(II) Absent manufacturer specifications, at a frequency necessary to preclude accumulation of soil or mold.

Observed gap at bottom of back door. 511-6-1.07(2)(m) - Outer Openings Protected (C) (m) Outer Openings, Protected.

1. Except as specified in paragraphs 2 through 5 of this subsection, outer openings of a food service establishment shall be protected against the entry of insects and rodents by:

(i) Filling or closing holes and other gaps along floors, walls, and ceilings;

(ii) Closed, tight-fitting windows; and

(iii) Solid, self-closing, tight-fitting doors.

2. The requirements in paragraph 1 of this subsection does not apply if a food service establishment opens into a larger structure, such as a mall, airport, or office building, or into an attached structure, such as a porch, and the outer openings from the larger or attached structure are protected against the entry of insects and rodents.

3. Exterior doors used as exits need not be self-closing if they are:

(i) Solid and tight-fitting;

(ii) Designated for use only when an emergency exists, by the fire protection authority that has jurisdiction over the food establishment; and

(iii) Limited-use so they are not used for entrance or exit from the building for purposes other than the designated emergency exit use.

4. Except as specified in paragraphs 2 and 5 of this subsection, if the windows or doors of a food service establishment, or of a larger structure within which a food service establishment is located, are kept open for ventilation or other purposes or a temporary food service establishment is not provided with windows and doors as specified under paragraph 1 of this subsection, the openings shall be protected against the entry of insects and rodents by:

(i) 16 mesh to 1 inch (16 mesh to 25.4 mm) screens;

(ii) Properly designed and installed air curtains to control flying insects; or

(iii) Other effective means.

5. The requirement in paragraph 4 of this subsection does not apply if flying insects and other pests are absent due to the location of the establishment, the weather, or other limiting condition.

Observed vents in the kitchen with rust and dust accumulation. 511-6-1.07(2)(j) - Heating, Ventilation, Air Conditioning, System Vents, designed to prevent contamination (C) (j) Heating, Ventilating, Air Conditioning, System Vents. Heating, ventilating, and air conditioning systems shall be designed and installed so that make-up air intake and exhaust vents do not cause contamination of food, food-contact surfaces, equipment, or utensils.

Observed buildup of slime in the interior of ice machine. Observed brown debris on ice machine chute along with mold-like build up on the interior portions of ice machine. PIC will cease using the ice machine until the ice machine is properly cleaned and sanitized. The PIC will email a copy of the completed work order to robert.lewis1@dph.ga.gov. 511-6-1.05(7)(b) - Food Contact Surfaces and Utensils - Cleaning Frequency (P, C) (b) Equipment Food-Contact Surfaces and Utensils.

1. Equipment food-contact surfaces and utensils shall be cleaned:

(i) Before each use with a different type of raw animal food such as beef, fish, lamb, pork, or poultry. It does not apply if the food-contact surface or utensil is in contact with a succession of different types of raw meat and raw poultry each requiring a higher cooking temperature as specified under DPH Rule 511-6-1.04(5)(a) than the previous type such as preparing raw pork followed by cutting raw poultry on the same cutting board; P

(ii) Each time there is a change from working with raw foods to working with ready-to-eat foods; P

(iii) Between uses with raw fruits and vegetables and with Time/Temperature Control for safety food; P

(iv) Before using or storing a food temperature measuring device; P and

(v) At any time during the operation when contamination may have occurred. P

2. Except as specified in paragraph 3 of this subsection, if used with time/temperature control for safety food, equipment food-contact surfaces and utensils shall be cleaned at least every 4 hours throughout the day. P

3. Surfaces of utensils and equipment contacting time/temperature control for safety food may be cleaned less frequently than every 4 hours if:

(i) In storage, containers of time/temperature control for safety food and their contents are maintained at temperatures specified under DPH Rule 511-6-1-.04 and the containers are cleaned when they are empty;

(ii) Utensils and equipment are used to prepare food in a refrigerated room or area that is maintained at one of the temperatures in the following chart and:

(I) The utensils and equipment are cleaned at the frequency in the following chart that corresponds to the temperature:

Temperature Cleaning Frequency

41ºF (5.0ºC) or less 24 hours

41ºF - 45ºF (>5.0ºC - 7.2ºC) 20 hours

45ºF - 50ºF (>7.2ºC - 10.0ºC) 16 hours

50ºF - 55ºF (>10.0ºC - 12.8ºC) 10 hours

and

(II) The cleaning frequency based on the ambient temperature of the refrigerated room or area is documented in the food service establishment.

(iii) Temperature measuring devices are maintained in contact with food, such as when left in a container of deli food or in a roast, held at temperatures specified under DPH Rule 511-6-1- .04;

(iv) Equipment is used for storage of packaged or unpackaged food, such as a reach-in refrigerator, and the equipment is cleaned at a frequency necessary to preclude accumulation of soil residues;

(v) The cleaning schedule is approved based on consideration of:

(I) Characteristics of the equipment and its use,

(II) The type of food involved,

(III) The amount of food residue accumulation, and

(IV) The temperature at which the food is maintained during the operation and the potential for the rapid and progressive multiplication of pathogenic or toxigenic microorganisms that are capable of causing foodborne disease; or

(vi) In-use utensils are intermittently stored in a container of water in which the water is maintained at 135ºF (57ºC) or more and the utensils and container are cleaned at least every 24 hours or at a frequency necessary to preclude accumulation of soil residues.

4. Dining counters and table-tops shall be cleaned and sanitized routinely after removing all soiled tableware and food trays shall be cleaned and sanitized after each use by one of the following methods:

(i) A two step method in which one cloth, rinsed in sanitizing solution is used to clean food debris from the surface and a second cloth in separate sanitizing solution is used to rinse;

(ii) Sanitizing solution is sprayed onto the surface and the surface is then wiped clean with a disposable towel;

(iii) If used for cleaning and sanitizing, single-use disposable sanitizer wipes shall be used in accordance with EPA-registered label use instructions; or

(iv) Other methods approved by the Health Authority.

(v) Food trays may be cleaned and sanitized the same as table ware.

5. Except when dry cleaning methods are used as specified under subsection (7)(e) of this Rule, surfaces of utensils and equipment contacting food that is not time/temperature control for safety food shall be cleaned:

(i) At any time when contamination may have occurred;

(ii) At least every 24 hours for iced tea dispensers including nozzles and consumer self-service utensils such as tongs, scoops, or ladles;

(iii) Before restocking consumer self-service equipment and utensils such as condiment dispensers and display containers; and

(iv) In equipment such as ice bins and beverage dispensing nozzles and enclosed components of equipment such as ice makers, cooking oil storage tanks and distribution lines, beverage and syrup dispensing lines or tubes, coffee bean grinders, and water vending equipment:

(I) At a frequency specified by the manufacturer; or

(II) Absent manufacturer specifications, at a frequency necessary to preclude accumulation of soil or mold.

Back to Top Back to Top | This page is being served from: CPDHJWHQ0QCFAA © Copyright 2024 Tyler Technologies All Rights Reserved.

Observed a staff member on the food preparation line lacking an effective beard restraint. PIC will provide beard nets by 12/20/24

511-6-1.03(5)(i) - Hair Restraints (C) (i) Hair Restraints.

1. Employees preparing or handling food shall use effective and clean, disposable or easily cleanable nets or other hair restraints approved by the Health Authority, worn properly to restrain loose hair including beards and mustaches longer than one half inch.

2. This does not apply to employees such as counter staff who only serve beverages and wrapped or packaged foods, hostesses, and wait staff if they present a minimal risk of contaminating exposed food, clean utensils and linens and unwrapped single-service and single-use articles.

Observed employee with no beard guard/restraint.

Observed the back door not properly sealed. PIC will install a door sweep below the back door to protect the outer openings and prevent pest entry by 12/23/24. 511-6-1.07(2)(m) - Outer Openings Protected (C) (m) Outer Openings, Protected.

1. Except as specified in paragraphs 2 through 5 of this subsection, outer openings of a food service establishment shall be protected against the entry of insects and rodents by:

(i) Filling or closing holes and other gaps along floors, walls, and ceilings;

(ii) Closed, tight-fitting windows; and

(iii) Solid, self-closing, tight-fitting doors.

2. The requirements in paragraph 1 of this subsection does not apply if a food service establishment opens into a larger structure, such as a mall, airport, or office building, or into an attached structure, such as a porch, and the outer openings from the larger or attached structure are protected against the entry of insects and rodents.

3. Exterior doors used as exits need not be self-closing if they are:

(i) Solid and tight-fitting;

(ii) Designated for use only when an emergency exists, by the fire protection authority that has jurisdiction over the food establishment; and

(iii) Limited-use so they are not used for entrance or exit from the building for purposes other than the designated emergency exit use.

4. Except as specified in paragraphs 2 and 5 of this subsection, if the windows or doors of a food service establishment, or of a larger structure within which a food service establishment is located, are kept open for ventilation or other purposes or a temporary food service establishment is not provided with windows and doors as specified under paragraph 1 of this subsection, the openings shall be protected against the entry of insects and rodents by:

(i) 16 mesh to 1 inch (16 mesh to 25.4 mm) screens;

(ii) Properly designed and installed air curtains to control flying insects; or

(iii) Other effective means.

5. The requirement in paragraph 4 of this subsection does not apply if flying insects and other pests are absent due to the location of the establishment, the weather, or other limiting condition.

Outer openings not protected with self-closing doors.

Observed no hot water in the ladies restroom. PIC corrected on site by turning on the hot water knob. Hot water not provided/shut off at employee handwash sink. 511-6-1.06(1)(g),(h) - Water Supply, Capacity; Pressure (Pf) (g) Capacity.

1. The water source and system shall be of sufficient capacity to meet the peak water demands of the food service establishment. Pf

2. Hot water generation and distribution systems shall be sufficient to meet the peak hot water demands throughout the food service establishment. Pf (h) Pressure. Water under pressure shall be provided to all fixtures, equipment, and nonfood equipment that are required to use water except that water supplied as specified under subsection (1)(k)1 and 2 to a temporary food service operation or in response to a temporary interruption of a water supply need not be under pressure. Pf

Observed employees' personal items in the storage area. Personal items must be stored in a designated area. 511-6-1.07(5)(j) - Using Dressing Rooms & Lockers, used for changing clothes and storing employee belongings (C) (j) Using Dressing Rooms and Lockers.

1. Dressing rooms shall be used by employees if the employees regularly change their clothes in the establishment.

2. Lockers or other suitable facilities shall be used for the orderly storage of employee clothing and other possessions.

Observed brown debris on ice machine chute along with mold-like build up on the interior portions of ice machine.

Observed employees/manager with long nails prepping food items. Fingernails longer than the tip of fingers requires the use of gloves.

Observed strong odor coming from grease trap.

Observed hand sink faucet in disrepair.

Observed outside of toaster with excessive build-up.

Observed dust build up on vents and ceiling tiles in prep area.

Observed light cover in disrepair in prep area.

Observed unapproved thawing method, Beans was observed thawing in standing water due to the chill warmer not working

Sprayer hose leaking in the three compartment sink area

Observed shelves above the steam well contained build up

Observed water under the hand sink due to the sink linking. PIC notified employee to mop water from the area. (COS)

Observed a heavy presence of flies throughout the facility/kitchen. Please have pest control to leave some pest control devices.

Observed a stall in the women's restroom with no toilet tissue. Employee put tissue in the restroom. (COS)

Observed water throughout the kitchen and under the hand sink. Please make sure the floor is clean and clear. PIC notified employee to get the water up. (COS)

Also, observed the walls and ceilings in the kitchen with dust build-up. Please clean these areas.

Observed no food items in the walk in cooler at temperatures of 41F or below.

Observed no paper towels in the men's restroom to properly dry hands. (Repeat)

Observed the establishment not demonstrating procedures or having a kit for cleaning vomit or diarrheal events. Please order a bodily fluid kit.(Repeat)

Observed the ice bin scoop stored in a container with black mold on the bottom. (Repeat)

Observed several flies throughout the kitchen area. No pest control records available for view. Please have pest control come to treat the facility and leave a copy of the report.

Observed white substance in a container with no common name to identify it. (Repeat)

Observed chicken boxes and prepped chicken in the walk in cooler with excessive water on the boxes and floor from a drain pipe in the cooler. This pipe will need to to be fixed, and the food will need to be stored on the opposite side. (Repeat)

Observed the faucet still broken on the prep sink in the kitchen. (Repeat)

Observed the pipe leaking water under the 3-compartment sink. (Repeat)

Observed the ventilation hood system with excessive dust and old grease debris. The system will need to be cleaned.

Observed the walk in cooler door not properly closing therefore making the walk in cooler and all food items higher than 41 F. The only way the door will close is if it's locked. The door will need to be repaired immediately. Please keep a log of all temperatures in the cooler and put ice on all items until the door is in good repair.

Observed an employee's drink on the paper towel holder, vent hood, and in the walk in cooler. PIC discarded all items. (COS) (Repeat)

Observed hand sink in kitchen with no paper towels. Paper towels were placed.(COS)

Observed hand sink in men's restroom with no hand soap. The person in charge added soap in the restroom. (COS)

Observed the establishment not demonstrating procedures or having a kit for cleaning vomit or diarrheal events. Please order a bodily fluid kit.

Observed the flour container with no lid, chicken stored uncovered; as well as buttermilk batter and biscuits. All items in storage must be covered.

Observed the ice bin scoop stored in a container with black mold on the bottom. (Repeat)

Observed white substance in a container with no name to identify it. (Repeat)

Observed chicken boxes stored in the walk in cooler with excessive water in the boxes from a drain pipe in the cooler. This pipe will need to to be fixed, and the food will need to be stored on the opposite end.

Observed the backflow system not maintained or in good repair. Excessive water was on the kitchen floor, closet near restrooms, and women's restroom. This will need to be repaired as soon as possible (6/12/2023).

Also, observed the faucet broken on the prep sink.

Observed the pipe leaking water under the hand sink in the kitchen by the fryers.

Observed an employee's sandwich stored in the storage closet. Observed an employee's drink stored on the prep table, Observed an open cup (no lid) stored on top of the pull out warmer. All items were discarded. (COS)

Observed the old inspection report not posted.