Milton, Fulton County

Campania Milton

12635 CRABAPPLE RD STE 310 ALPHARETTA, GA 30004

Food
Latest score
96
May 26, 2026
City
Milton
County
Fulton
Inspections
4

Score history

Inspection scores over time for this facility.

Inspection history

Georgia inspection history is score-based, with violations grouped under each recorded inspection.

May 26, 2026

Routine

Score: 961 violation

4-2A - food stored covered

Regulation: 511-6-1.04(4)(c)1(iv) - packaged & unpackaged food, food stored covered(c)

4 ptsCorrected: NoRepeat: No

Observed multiple food containers in reach-in cooler stored without a lid. Advised PIC to cover containers when storing them in the reach-in. 511-6-1.04(4)(c)1(iv) - Packaged & Unpackaged Food, food stored covered(C) (iv) Except as specified under paragraph 2. of this subsection and when cooling as specified in DPH Rule 511-6-1-.04(6)(e)2.(ii), storing the food in packages, covered containers, or wrappings, except for loosely covered or uncovered containers in which food is being cooled if protected from overhead contamination;

Dec 5, 2025

Routine

Score: 962 violations

10D - food properly labeled; original container

Regulation: 511-6-1.04(8)(b) - expired foods (p)

3 ptsCorrected: YesRepeat: No

Observed expired soda on the drink lines. PIC discarded them.

15B - warewashing facilities: installed, maintained, used; test strips

Regulation: 511-6-1.05(3)(h),(i),(j) - temperature measuring device, manual warewashing; sanitizing solutions, testing device (pf)

1 ptsCorrected: NoRepeat: No

Observed no chlorine test strips on site. CA - PIC will acquire chlorine test strips along side quats ones.

Nov 8, 2024

Routine

Score: 962 violations

11A - proper cooling methods used: adequate equipment for temperature control

Regulation: 511-6-1.04(6)(e) - cooling methods (pf, c)

3 ptsCorrected: NoRepeat: No

Observed a large container of bolongese cooling in the meat sink fully covered without being stirred.

  1. Cooling shall be accomplished in accordance with the time and temperature criteria specified under DPH Rule 511-6-1-.04(6)(d) by using one or more of the following methods depending on the type of food being cooled:

(i) Placing the food in shallow pans; Pf

(ii) Separating the food into smaller or thinner portions; Pf

(iii) Using rapid cooling equipment; Pf

(iv) Stirring the food in a container placed in an ice water bath; Pf

(v) Using containers that facilitate heat transfer; Pf

(vi) Adding ice as an ingredient; Pf or

(vii) Other effective methods. Pf

  1. When placed in cooling or cold holding equipment, food containers in which food is being cooled shall be:

(i) Arranged in the equipment to provide maximum heat transfer through the container walls; and

(ii) Loosely covered, or uncovered if protected from overhead contamination during the cooling period to facilitate heat transfer from the surface of the food.

PIC had the sauce portioned out into smaller portions and will purchase ice wands for batch cooling.

15A - food and nonfood-contact surfaces cleanable, properly designed, constructed, and used

Regulation: 511-6-1.05(6)(b) - cutting surfaces (c)

1 ptsCorrected: NoRepeat: No

Observed several cutting boards that were heavily damaged by repeated use. Surfaces such as cutting blocks and boards that are subject to scratching and scoring shall be resurfaced if they can no longer be effectively cleaned and sanitized, or discarded if they cannot be resurfaced. PIC will ensure that the cutting boards are resurfaced or replaced.

Jul 25, 2023

Routine

Score: 991 violation

15A - food and nonfood-contact surfaces cleanable, properly designed, constructed, and used

Regulation: 511-6-1.05(2)(c) - multiuse food-contact surfaces (pf)

1 ptsCorrected: NoRepeat: No

Observed heavily scored cutting boards in grill prep that were not in use.

  1. Multiuse food-contact surfaces shall be: (i) Smooth; Pf (ii) Free of breaks, open seams, cracks, chips, inclusions, pits, and similar imperfections; Pf (iii) Free of sharp internal angles, corners, and crevices; Pf (iv) Finished to have smooth welds and joints; Pf and (v) Except as specified in paragraph 2 of this subsection, accessible for cleaning and inspection by one of the following methods: (I) Without being disassembled, Pf (II) By disassembling without the use of tools, Pf or (III) By easy disassembling with the use of handheld tools commonly available to maintenance and cleaning personnel such as screwdrivers, pliers, open-end wrenches, and Allen wrenches. PIC will discard and replace them.